Beachcomber 538 Instrucciones de operaciones descargar pdf (Pagina 12)

STARTUP

When your hot tub is ﬁrst activated, it will go into priming mode

(after displaying some conﬁguration information). The priming

mode will last up to 4 minutes; then circulation will start, then heat

light will come on for 6 seconds, and then ﬂicker for

90 seconds

Then heater will come on to heat water to set temperature. It is

recommended that priming mode be allowed to ﬁnish, preventing

any pumps from operating dry. If you are positive all pumps are

primed you can exit priming mode early by pressing .

TEMPERATURE ADJUSTMENT

Temp range is: (80°F - 104°F/26.0°C – 40.0°C) The factory pre-set

temperature is set at 100°F/37.5°C. The last measured temperature

is constantly displayed on the LCD. See edit menu in Owner’s Guide

to select F° or C°.

Note: On non HushPump™ hot tubs the

current water temperature will only be displayed if the 2

speed ﬁlter pump has been running for two minutes.

Press the button once to display the temperature

previously set. To change the set temperature, press the

button a second time before the LCD stops ﬂashing. Each

press of the will continue to cause the set temperature

to increase or decrease depending on what direction was last

chosen. Each press to follow will change the set temperature

in the same direction. If the opposite direction is desired,

release the pad and let the display revert to the actual water

temperature. Press the pad to display the set temperature, and

again to make the temperature change in the desired direction.

Actual water temperature will reappear on the display after

changing the temperature setting.

HEATING MODES

A button combination is used to switch between Standard,

Economy, and Sleep modes. Press

followed by to

enter mode programming, press to cycle through to the

desired mode (LCD ﬂashes until conﬁrmed), then press

conﬁrm selection.

Standard Mode maintains the set temperature at all times.

STD will appear on the display momentarily when you switch

into Standard Mode.

Economy Mode heats the hot tub to the set temperature only

during ﬁlter cycles. ECN will appear solid when the temperature

is not current and will alternate with the temperature when the

temperature is current. On a HushPump™ equipped hot tub the

heater will come on if required for up to 2 hours twice a day (total

of 4 hrs). Pressing while in economy mode puts the hot tub

in Standard-In-Economy mode,

SE, which operates the same

as standard mode, then reverts to Economy mode automatically

after 1hour. Use this mode to activate the heater if using tub

when not in ﬁlter cycle. During this time, pressing followed

by will revert the mode to Economy immediately.

Sleep Mode heats the hot tub within 20°F (11°C) of the set

temperature only during ﬁlter cycles. SLP will appear on the display

until mode is changed. Use this mode when going on holidays.

MASSAGE

Press the button once to activate the pump’s low speed, again

for the pump’s high speed, and once more to turn off the pump. The

pump’s low speed turns off automatically after 2 hours. The pump’s

high speed will turn off automatically after 15 minutes. Massage

pump comes on for a 1 minute purge at the start of each ﬁlter cycle.

TURBO (OPTIONAL)

Press the button to turn Turbo on and off. Turbo will

automatically turn off after 15 minutes. Turbo comes on for a 10

second purge at the start of each ﬁlter cycle.

LIGHT

Press the button to turn the hot tub light on, press again to

turn off. Light will automatically turn off after 3 hours.

Heat

LightTemp

TurboMassage

Heat

LightTemp

TurboMassage

Heat

LightTemp

TurboMassage

ET-5 CONTROL PANEL INSTRUCTIONS

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 31 32

Comentarios a estos manuales

Sin comentarios

Beachcomber 538 Instrucciones de operaciones Pagina 12

Comentarios a estos manuales