Beachcomber 538 Instrucciones de operaciones descargar pdf (Pagina 11)

TIME OF DAY AND FILTER CYCLES SETTING

On all systems, the 2 speed ﬁlter pump or HushPump™

and ozone generator will run during ﬁltration. There are two

ﬁlter cycles per day. The start/end times of each cycle are

programmable. Programming ﬁlter times on HushPump™

equipped hot tubs are used to tell the system how many hours a

day to turn the heater on when in Economy mode.

To Program:

1. Press then .

2. Use the

and buttons to adjust the time of

day in hours, press the again to adjust the time in

minutes. Use the and buttons to adjust the

minutes. Press to enter new time.

3. You will see

PROGRAM, FILTER 1 (F1), START

TIME appears on the display. Press or

to choose the ﬁlter start time hour. Enter the hour by

pressing .

4. Press

or to choose the ﬁlter start time

minutes. Each press will change the start time by 5

minutes. Enter the minutes by pressing

5. Press

to see the PROGRAM, FILTER 1(F1),

END TIME. Adjust the time as done above.

6. Press

to see the PROGRAM, FILTER 2(F2),

START TIME. Proceed as above.

7. Press

to see PROGRAM, FILTER 2(F2),

END TIME. Adjust the time as done above.

8. The time that now appears allows you to turn your hot tub

light on automatically. Adjust time as done above.

9. Program the time you want your light to turn off.

10. Press

will enter the new ﬁlter cycle times into the

system and display the current water temperature.

PANEL INVERSION

Press the or button, followed by the or

button to change the numbers in the display to read upside

down. Press the same sequence to set back.

LOCKING THE PANEL

Press , 1 then within 3 seconds. When locked, the

PL indicator light will light up. All buttons are frozen except the

button. To unlock the panel, press , 1 then .

LOCKING THE SET TEMPERATURE

Press or then , 1 and within 3

seconds to activate the lock. The TL indicator light will light up

when temperature is locked. To unlock the set temperature, press

or then

, 1 and .

PERIODIC REMINDER MESSAGES

(press the button to reset a displayed reminder

message)

rPH: Test and adjust pH chemical levels as per Beachcomber

instructions. Reminder is every 7 days.

rCL: Remove, clean, and reinstall Microﬁlter as per Beachcomber

instructions. Reminder is every 30 days.

rt9: Test & reset GFCI as per Beachcomber instructions.

Reminder is every 30 days.

rdr: Drain and reﬁll hot tub as per Beachcomber instructions.

Reminder is every 90 days.

rCO: Clean and condition Heatshield as per Beachcomber

instructions. Reminder is every 180 days.

rCH: Install new Microﬁlter. Reminder is every 365 days.

To suppress reminders, refer to the edit menu on page

16.

DIAGNOSTIC DISPLAY MESSAGES

OHH or OHS: Overheat-DO NOT ENTER HOT TUB

ICE: Potential Freeze

SNA: Hot tub is shut down

SNB: Hot tub is shut down

SNS: Sensor out of balance

HFL: Could indicate ﬂow problem

LF: Persistent low ﬂow problems

DR: Inadequate water detected

DRY: Inadequate water detected

PR: Hot tub in priming mode

- - : Temperature unknown

---: Temperature not current or in Economy or Sleep mode.

PLEASE REFER TO TROUBLE SHOOTING GUIDE

STARTING ON PAGE 23 FOR A COMPLETE

EXPLANATION OF DIAGNOSTIC MESSAGES.

SHOCK HAZARD!

NO USER SERVICEABLE PARTS.

DO NOT ATTEMPT SERVICE OF THIS CONTROL. CONTACT

YOUR DEALERSHIP OR SERVICE PROVIDER FOR

ASSISTANCE. FOLLOW ALL OWNER’S GUIDE POWER

CONNECTION INSTRUCTIONS. INSTALLATION MUST

BE PERFORMED BY A LICENSED ELECTRICIAN AND

ALL GROUNDING CONNECTIONS MUST BE PROPERLY

INSTALLED.

WARNING

TAMPERING WITH OR MODIFYING

THIS EQUIPMENT MAY VOID YOUR

GUARANTEE.

WARNING

ALWAYS TEST WATER TEMPERATURE

PRIOR TO ENTRY USING THE TOPSIDE

CONTROL PAD. ENSURE COMFORT BY ALSO CHECKING

WATER WITH A THERMOMETER.

WARNING

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 31 32

Comentarios a estos manuales

Sin comentarios

Beachcomber 538 Instrucciones de operaciones Pagina 11

Comentarios a estos manuales